Your Complete Tutorial for Bathtub Installation
Your Complete Tutorial for Bathtub Installation
Blog Article
The publisher is making a few great points about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround overall in this great article further down.
Setting up a bathtub isn't exactly brain surgery, yet it does require strong plumbing, woodworking, and occasionally, tiling skills. Replacing an old tub with a brand-new one is likewise a moderately challenging job. If the old bathtub is conveniently available, the task can relocate speedily; if you need to open a wall surface to eliminate the old tub as well as position the new bath tub, the job is much harder. In either case, the project is within a house handyman's abilities, although you will certainly need an assistant to move out the old bathtub as well as embeded in the new one. Make sure you have actually certified yourself for the job and fit trying it. Instead of hiring a service provider to take control of a halfway-completed project, it is far better to think about using one before you start. Chances are you may require a professional plumber to make tube connections.
This post will certainly assist you mount a brand-new bathtub in your shower room if you have actually currently bought a new tub and don't need to transform the setup of your previous water supply pipes.
Your tools and material list should comprise the following:
Preparing for the Installation
First of all, the supporting frame provided with the bath should be fitted (if called for) according to the maker's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to see to it that if the tap features a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise sensible to fit a supporting plate under the faucets device to prevent stress on the bath tub.
Fit the flexible tap ports to the bottom of both faucets making use of 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. See to it you utilize all of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom must now be ready to be suited its final placement.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, after that the first thing you need to do is disconnect the water. After doing so, turn on the taps to drain pipes any kind of water staying in the system. The procedure of getting rid of the existing taps can be fairly troublesome because of the restricted accessibility that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a cloth all set for the remaining water that will certainly come from the pipelines. Once the supply pipelines have actually been gotten rid of, make use of the same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from transforming during this procedure. When the taps have actually been removed, the holes in the bath/basin will need to be cleansed of any old sealing substance.
Prior to moving on to fit the new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bathtub
Using the two wood boards under its feet, position the bath tub in the called for placement. The wood boards are practical in uniformly spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four small factors.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the tub up until the spirit level reads level.
To set up taps, fit all-time low of the outermost flexible faucet port to the proper supply pipe by making a compression sign up with; then do the very same for the other faucet.
Activate the water system and inspect all joints and also brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as additionally check the overflow outlet as well as the typical electrical outlet for leakages.
Ultimately, fix the bath paneling as described in the producer's instruction manual. Tiling as well as sealing around the tub ought to wait up until the tub has been used at least once as this will certainly resolve it right into its final position.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic connector to avoid damages to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, then you will certainly need reducing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin making sure that the washing machines are in place between the faucet and the sink. Protect the faucet in place with the maker given backnut. Once the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical faucet adapters. The previous kind needs to be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bathroom satisfies the tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to crack an inflexible seal, causing the water to penetrate the wall surface between the bathroom and the tiling, bring about problems with dampness and possible leakages to the ceiling below.
You can choose from a range of coloured sealants to blend in your fixtures and fittings. They are marketed in tubes and also cartridges, and can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill up the bath tub with water before securing, to allow for the activity experienced when the bathtub is in usage. The sealer can fracture relatively very early if you do not think about this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise conveniently available on the market. It is suggested to fit the floor tiles making use of water-resistant or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like reading up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Try to leave feedback further down. We'd be interested to see your thoughts about this blog post. In hopes that you visit us again in the future. So long as you enjoyed reading our page please remember to share it. Thank you for taking the time to read it.
Call Today Report this page